News · 18 November 2026

How to Change Windshield Wiper Blades in 60 Seconds

Windshield wiper blade clearing rain from a windshield

Short answer: changing a wiper blade takes about 60 seconds per blade and no tools on most cars: lift the arm away from the glass, release the old blade, slide the new one on until it clicks, lower the arm gently, and test it with the washer. The only part that takes any time is getting the right size first — measure the old blade end to end, or send the car make, model and year. Do the job with the wipers switched off, and never let a bare metal arm snap back onto the glass.

Before you start: get the right size and adapter

Measure both front blades — driver and passenger blades are often different lengths. WEILONG front blades cover 12″ to 28″ (300–700 mm) in 12 sizes, including the odd 17″, 19″ and 21″ sizes, and rear blades (WL-623) cover 8″ to 16″ — see the wiper blade size chart. Size is only half the fit: the adapter must match the arm as well. Most cars use a hook arm, which fits the hook-type blades (WL-616, WL-617, WL-618, WL-621). Other cars use push-button, pin or bayonet arms, which need a multi-adapter blade — for example the WL-818 Multi-Fit with its 19-adapter LB system.

Step 1: Park the wipers and lift the arm

Switch the wipers off and turn the ignition off. On many cars the wipers rest under the edge of the bonnet, so move them to the service or park position first, as the owner's manual describes. Once the arm can move freely, lift it away from the glass until it stands up on its own. Hold it with one hand for the whole job: a bare metal arm that snaps back can crack a windshield.

Step 2: Release the old blade

Turn the blade at right angles to the arm — this takes the tension off the connector. On a hook arm, press the small tab where the blade meets the hook and slide the blade down and out. On a push-button blade, press the release button and slide it off. Do not pull hard: if it does not move, you have the wrong tab. Note which way the old blade faced; the new one goes on the same way round.

Step 3: Slide the new blade on until it clicks

Take the new blade out of its packaging and, if it came with a choice of adapters, fit the one that matches your arm first. Slide it on in the reverse of step 2 — hook blades go up into the hook, push-button blades slide on until the button pops out. You should hear and feel a clear click. Tug the blade gently along the arm: if it moves, it is not locked — refit it. Never drive with a blade that is only half-seated; it can fly off at speed.

Step 4: Lower the arm gently and test

Lower the arm back onto the glass slowly, guiding it down by hand — do not let it drop. Repeat steps 1 to 4 on the other side, remembering the two front blades may be different lengths, so do not swap them. Then run the washer and watch one full sweep. A good fit wipes clean in a single pass, with no streaks, skipping or noise. If a brand-new blade streaks, clean the glass and rubber first — road film causes streaks too. If the streaks stay, the blade is the wrong size or adapter for that arm.

Rear blades and winter blades: the same 60 seconds

Rear wipers work the same way, only smaller — WL-623 rear blades are 8″ to 16″ and usually clip on with a single press fitting. In winter, lift the blade off the glass before switching the wipers on: a blade frozen to the glass can tear its rubber in one pass. For snow and ice, the WL-629 snow wiper is rated to −40°C — see the winter wiper buying guide. And if your old blades show any of the 5 signs they need replacing, change them now, before the next rain, not during it.

What to order when it is time

Order by size and adapter, not by car brand alone: send the car make, model and year, or the length of the old blade in inches, plus a photo of the arm end if you are unsure of the adapter. WEILONG supplies boneless, hybrid, metal-frame, winter, rear and truck and bus blades — front 12″ to 28″, rear WL-623 8″ to 16″, bus blades up to 40″. For distributors, the minimum order is 1,000 pieces, samples take 7–15 days and bulk orders 20–30 days, loading from Qingdao or Tianjin ports, with a 30% T/T deposit and 70% before delivery.

Frequently asked questions

How long does it take to change wiper blades?

About 60 seconds per blade once you have the right size in hand — lift the arm, release the old blade, slide the new one on until it clicks, lower the arm and test it. The whole job for both front blades is usually under five minutes, including measuring.

Do I need tools to change wiper blades?

No tools are needed for most cars. Hook-arm blades and multi-adapter blades such as the WEILONG WL-818 clip on by hand. Only check the owner's manual first if your car hides the wipers under the bonnet — many cars need the wipers moved to a service or park position before the arms can be lifted.

What size wiper blades do I need?

Measure the old blade end to end, or send the car make, model and year. WEILONG front blades cover 12 to 28 inches (300-700 mm), rear blades 8 to 16 inches, and bus blades up to 40 inches. The two front blades are often different lengths, so measure both.

Changed yours yet?

If your blades streak, squeak or skip, the 60-second swap is the cheapest safety fix on the car — and if you buy for resale, stock the sizes your market asks for most:

Chat on WhatsApp   Jady@weilongwipers.com

← Back to all buying notes